Skip to main content

Blog entry by Kazuko Marsh

Keep your Furnace in Good Shape with Furnace Maintenance

The maintenance of your furnace is essential to owning a property. Regular maintenance by a licensed HVAC expert is the best way to accomplish this.

Check that the circuit-breaker of your furnace has not been tripped. This is a precaution to avoid carbon monoxide intoxication.

Check Your Thermostat

The thermostat, an electronic device, transmits signals that tell the furnace to turn on and off. This thermostat has an LCD screen which displays your heating schedule, as well the indoor temperature. If your display is blank it means that you need to replace the batteries in your thermostat.

Most thermostats are wired and receive power through the circuit breaker in your home and the electrical grid of the city, while others rely on batteries for their operation. If the latter type of thermostat is experiencing problem, it may emit an unrelenting hum and you'll hear a clicking noise when a signal is received by the furnace.

It could be that your furnace is humming constantly. This could be because of a clogged or broken condensation line. A trained HVAC specialist in East York can quickly diagnose the problem and repair it before it gets worse.

If the blower and furnace are not operating, it could be that the thermostat is malfunctioning. The thermostat might be disconnected. The fan would not receive enough power to distribute the air.

To fix this problem to fix the issue, open the door to the furnace and pull out all wires with the help of a screwdriver. Connect the wires to the other ends. This will restore the connection between the heater and the thermostat.

You can also remove the pilot assembly by removing the furnace access panel. It has a reset button that you can push to restore the gas flow. Take care to remove the assembly carefully, as natural gas is highly flammable. You should check the gas valve before you move on to other troubleshooting.

Check the Blower

When you turn on your furnaceand start the blower, the air will flow through the ducts of your home. It could be that your furnace isn't blowing enough. It is possible that insufficient air flow will also impact the humidity level of your home.

You can check the blower easily by switching off your system. Look for the cabinet door that houses the blower. Open the door, and remove the panel. The rotor can be fixed with screws or snap clips. Take out the rotor with a screwdriver and pliers.

Once you have replaced the rotor, shut the panel and reconnect the power. The flame sensor in your furnace may be malfunctioning if the blower is still not working. This safety device detects the presence of flame before allowing the gas valve to be opened. Over time the metal rod can become coated with dust or carbon deposits caused by combustion. If your system stops working properly, air conditioning repair it will be shut off for safety.

By examining the blower's door for damage, you can tell if it has a faulty flame sensor or if its motor is damaged. In addition, hvac repair near me you must examine the ductwork in your home for leaks and moisture accumulation. It is possible that if any of these problems are present, your system might not be working properly. You may need to replace a part or repair the system.

Utility bills that are high can be another indication of a system not functioning properly. When you liked this informative article along with you want to receive more info regarding air balance testinggenerously stop by the web-site. The higher your energy bills, the more likely your system will not function properly. If your energy bills are much higher, this could be an indication that your heating system isn't working properly.

Check the Filter

The furnace filter should be replaced between three and six months. A high efficiency, clean furnace filter can lower your energy bill and increase the lifespan of the furnace. The heat exchanger can overheat if the air flow is restricted by a clogged filter. This can be a fire hazard and your system's computer will shut it down after it has overheated four or more times.

The ability of the air blower to move the air around your home can be affected by a dirty or clogged filter. Remove the filter, and listen for air moving through the vents. If you don't notice any sound, then it's probably time to replace your filter.

You can also look out for other signs that the furnace is not working correctly. A strong odour is an example. It may be a sign of carbon monoxide produced from a poor burn. Test the pressure gauge on your furnace.

This is another sign of afurnace that isn't functioning properly. The pilot light may not have been lit. It may be a simple fix. The technician can check the thermocouple, pilot flame sensor and other components to find the source of the problem.

Search for safety features such as the service panel or door switch that will stop the system from working if the panel is removed or opened. Also, make sure the panel is securely fastened to its frame. It will help keep away children and intruders.

If your air handler is located in a crawlspace or attic with no stairs, you will need to find a solution for the homeowners and service technicians. You should also check for signs of biological growth and moisture if a duct leads directly to the intake air from outside (see images 2 and 9).

Check the filter compartment as well as the opening and the panel of access. All accessible ductwork should be examined to check for sagging or air leaks as well as loose or missing insulation. Listen for whistling sounds, which indicate that the ducts weren't properly sealed.

Be sure to inspect the combustion chamber

Furnaces generate warm air via a heating system that involves burning fuel. This heated air is then sent into your home using ducts. The combustion gases are then expelled from the heat-exchanger. If there's a problem, you may find that your home is contaminated with toxic carbon monoxide. This can be avoided by identifying problems early and performing regular maintenance.

The healthy furnace will make a sound similar to whirring. If it makes other sounds like banging or rattling that could be a sign of a malfunction. A professional will be able to identify and correct the sound before they cause a problem.

A damaged stove may make loud noises and also have other signs. For example, a clogged combustion chamber or exhaust vent. With time, the dust on the flame detector can build up. It may not be able to detect pilot lights or ignite a furnace. The system could be forced to cycle on and off continuously, rather than running at maximum capacity.

A circuit breaker trip is another sign of a possible problem. This switch controls your furnace's power, so if it is switched off, you won't be in a position to start the system. If you find that your circuit breakers are off, turn them back on.

You can also check the combustion chamber to determine whether it's in good condition. If the system is working, you will be able to see the flame beneath the ignitor. If you see the part glowing or showing other marks, this means it is not properly igniting. It should be replaced by a professional.

The flue pipe that delivers combustion gas outdoors can be blocked by anything from a bird's nest to a fallen branch. You need to install a carbon dioxide detector because this can lead to carbon monoxide entering your home. An HVAC technician can seal the source of a leak and replace the flue pipe if you have a leak.

  • Share

Reviews


  
Contact Us x